Microstructural Evaluation Research Articles

Engineered Cementitious Composites with Super-Sulfated Cement: Mechanical, Physical, and Durability Performance

This study aimed to bridge a research gap by exploring the utilization of super-sulphated cement (SSC) in engineered cementitious composites (ECCs) as a sustainable alternative to ordinary Portland cement (OPC)-based mixtures. The SSC was designed with slag, gypsum, and a small amount of OPC. The primary objective was to investigate the effects of incorporating SSC, both with and without fly ash (FA), at various FA/SSC ratios between 0 and 1.5. A comprehensive evaluation was conducted to assess the performance of the ECC-SSC mixtures, including the compressive and flexural strengths, ductility, ultrasonic pulse velocity, rapid chloride permeability, and drying shrinkage. Additionally, advanced microstructural evaluation techniques such as scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analysis as well as X-ray diffraction (XRD) analysis were employed to analyze the reaction products in selected mixtures. The results showed that the ECC mixture produced with SSC exhibited comparable strength to the ECC-OPC. In general, all the SSC-based ECCs fulfilled the criteria for various engineering applications, especially when the fly ash to SSC ratios were 0 and 0.8. In addition, ECCs with FA/SSC ratios of 1.2 and 1.5 showed ultra-ductile performance higher than the control ECC. Interestingly, all the FA-based ECC-SSC presented lower shrinkage characteristics than the control OPC-based ECC.

BIOACTIVE PROPERTIES AND MORPHOLOGICAL FEATURES OF HYDROXYAPATITE/ZINC OXIDE HYBRID REINFORCED BIO-BASED EPOXY RESIN COMPOSITES FOR DENTISTRY

In this work, hybrid reinforced epoxy biopolymer composites were developed using natural hydroxyapatite and zinc oxide (nHAp/ZnO). The epoxy was reinforced with varying addition of nHAp and ZnO in the steps of 3, 5 and 7 wt. % respectively using stir casting molding process. The developed composites were immersed in simulated body fluid (SBF) at 37oC to determine their bioactivity. Microstructure evaluation using scanning electron microscopy was also used to assess the morphology of the developed composites before and after in vitro test, respectively.The microstructure evaluation in vitro showed good deposition of white-like layers on the surface indicating good bioactivity reaction with the SBF and affirm that the developed biopolymers will react well with living tissue when used in vivo. However, hybrid sample BP5HB showed better apatite-like layer deposition.

Role of oscillation frequency and amplitude on the microstructure and properties of linear friction welded nickel aluminium bronze joints

This study explores the influence of oscillation frequency and amplitude on the quality of linear friction welded joints using as-cast nickel aluminium bronze. Welding was conducted at 30 Hz, 50 Hz, and 70 Hz oscillated frequencies and amplitudes of 1.5 mm, 2 mm, and 3 mm. The joint’s performance was thoroughly investigated through systematic analysis, including macrostructure examination, peak interfacial temperature measurement, microstructure evaluation, strain assessment, cooling rate determination, microhardness testing, and tensile property characterization. The width of the weld zone varied from 183 μm to 297 μm, and the thermomechanical affected zone (TMAZ) area ranged from 4.48 mm2 to 14.79 mm2 across different process parameters. In the parent material, the volume fraction of the β-phase was as low as 20.2%, contrasting with the dominant α-phase at 79.8%. The average grain size of the lamellar and globular α-phase mixture was 26.4 μm. Notably, the weld zone exhibited extremely refined α-phase grains, with diameters less than 5 μm in all cases. The volume fraction of the β‘-phase increased significantly with higher frequencies, from 15.299% at 30 Hz to 26.98% at 50 Hz, peaking at 40.08% at 70 Hz, leading to varying k phases. This variation in microstructure had a substantial impact on mechanical properties. Tensile strength ranged from 503 MPa to 582 MPa, while ductility varied from 13.5% to 21.7%. Additionally, the hardness of the parent material increased from approximately 155 Hv to 260 Hv. This study demonstrates that controlling the oscillation frequency and amplitude in linear friction welding processes can yield consistent, high-quality welds in nickel aluminium bronze.

EXPLORING STRENGTHENING MECHANISMS OF ULTRAFINE-GRAINED Fe35Mn27Ni28Co5Cr5 HIGH-ENTROPY ALLOY PROCESSED BY SEVERE COLD ROLLING PROCESS

This study describes the strengthening mechanisms of an ultrafine-grained (UFG) Fe35Mn27Ni28Co5Cr5 high-entropy alloy (HEA) processed by severe cold rolling (SCR) process at room temperature. Microstructural evaluations were performed by field emission scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The findings demonstrated that the development of deformation microstructures consisted of a single face-centered cubic (FCC) phase with stretched grains along the rolling direction and lamellar deformation bands after a 90 % reduction in thickness. Using the Nix-Gao model, the dislocation density was determined by measuring the microhardness indentation size effect. The results indicated that an increase in rolling deformation leads to an increase in dislocation density. The dislocation density increased from 2.28 ×109 cm-2 for as-homogenized specimen to 8.65 ×109 cm-2 after 90 % reduction in thickness. The yield strength of the UFG Fe35Mn27Ni28Co5Cr5 HEA was 5.2 times (1155 MPa) higher than that of the as-homogenized state (225 MPa). Finally, an assessment was conducted on the relative contributions of individual mechanisms, such as dislocation and grain refinement, to the strengthening of the Fe35Mn27Ni28Co5Cr5 HEA.

SYNTHESIS AND CHARACTERIZATION OF PURE AMORPHOUS SILICON OXIDE FROM TREATED KAOLINITIC CLAY USING CHEMICAL EXTRACTION

Pure silicon oxide was produced in this study utilizing a sodium silicate solution made from Kankara clay as a precursor. The Kankara clay that was obtained from Nigeria was first beneficiated to produce pure dried powder clay. After that, the dried powdered clay was treated with heat activation and acid leaching, respectively. In a 500 mL Erlenmeyer flask, appropriate amounts of each clay (raw, thermally treated clay, and leached clay) were reacted with 3M NaOH solution. The flask was heated to 200°C and stirred continuously for 3 hours on a magnetic stirring hot plate connected to a reflux condenser. The solution was filtered to yield sodium silicate solution, which was then precipitated with 3M HCl while constantly stirring to produce a gelly-like white substance. The gel was aged for 18 hours, then washed with de-ionized water several times before being dried at 80°C for 12 hours to get pure white silica particles, which were subsequently described. The XRD analysis revealed that the silicon oxide synthesized is amorphous, but the microstructure evaluation revealed particles aggregation, which is usual in sol-gel synthesized powder.

Graphene reinforced ceramic matrix composite (GRCMC) – state of the art

Abstract Ceramic Matrix Composites (CMC) are widely used for manufacturing automobile parts aircraft components, biomedical and electronic devices. In recent years, graphene has found extensive applications in various fields like effective reinforcement in the development of metal matrix, polymer matrix and ceramic matrix composites. Literature reveals that more focus was on polymer and metal matrix composites reinforced with graphene when compared to ceramic matrix composites. In this manuscript, the effect and suitability of graphene as a reinforcement for fabricating ceramic matrix composite are presented. Further, the property evaluation, including mechanical and physical, characterization and microstructural evaluation of the CMCs developed with graphene as reinforcement is elaborated. The investigation of the reinforcing mechanisms and failure behavior of ceramic matrix composites reinforced with graphene, together with the development of novel processing techniques to solve manufacturing difficulties, are key areas of focus. Although many investigations have concentrated on enhancing the mechanical and electrical characteristics of ceramics by integrating graphene, more investigation is required to investigate the interfacial interaction between graphene and the ceramic matrix, as well as the influence of graphene size on the properties of the composite. Furthermore, there is a need for future research to explore the possibility of using graphene-reinforced ceramic composites in several multifunctional applications, including microwave absorption, electromagnetic interference shielding, ballistic armors, self-monitoring damage sensors, and energy storage and conversion. Future research should focus on developing innovative processing procedures that guarantee the uniform distribution and precise alignment of graphene sheets within the ceramic matrix. The incorporation of graphene into ceramic matrix composites presents novel prospects for augmenting the characteristics and capabilities of ceramics, rendering it a very interesting area for further investigation.

Experimental Evaluation of Mechanical Properties, Micro Structure and Post-Fire Strength of Fiber Reinforced Geopolymer Concrete

Geopolymer mixtures offer an enhanced alternative to implement an eco-friendly solution in construction industry. These mixtures exhibit similar or better mechanical and structural properties in comprising of cement and can use recycling and by-product materials. Against this background, an eco-friendly advantageous were achieved from the engineers and researchers by using waste materials to replace cement and attention to reduce CO2 emission during its procedure. This study attempted to evaluate compressive and tensile strength, micro structure and post-fire characteristic of the geopolymer mixtures. For this aim, the geopolymer mixtures were exposed to elevated temperature between 200, 500 and 800 0C. Then, the post-fire and mechanical behaviour were investigated. The proposed research supported the slight decrease in the GPC's compressive stress by fibres, and the 1.25% PP fibres displayed the least performance, indicating nearly 13% decrease than the unreinforced mixtures. As exhibited by the post-fire behaviour of mixtures, the GPC's compressive strength increased first for all mixes but in the range of 400 - 800°C it decreased at a higher rate because of the geopolymer matrix-related dehydration. Besides, fiber melting under high temperatures and the thermal reaction procedure related to free water evaporation reduce the mechanical properties under temperatures ranging from 400°C to 800°C. DOI: https://doi.org/10.52783/pst.349

Vermicompost and millicompost as a resource in sustainable agriculture in semiarid: decomposition, nutrient release, and microstructure under the action of nitrogen and organic-mineral fertilizers.

With the expansion of organic agriculture, research is needed to indicate economically and ecologically viable fertilizer options, especially in semiarid regions, with low soil organic matter and nitrogen content. In the Brazilian semiarid region, vermicomposts are widely used by farmers and are scientifically investigated; however, there is no information for millicompost, a new type of organic compound that has shown very promising results in other regions. Thus, this study aimed to analyze the decomposition rate, nutrient release, and microstructure evaluation of vermicomposts from different sources and of millicompost produced from plant residues, with the application of mineral nitrogen-urea and organo-mineral fertilizer in the Brazilian semiarid region. The experimental design was a randomized block in a 4 × 3 factorial scheme, with four replicates; four organic composts (millicompost, commercial vermicompost, vermicompost from bovine manure, vermicompost from goat manure); and three types of fertilization (without fertilizer, with mineral-urea and organo-mineral fertilizer). The organic composts were decomposed using litterbags at the soil surface. The variable's decomposition rate and the nutrient release were evaluated at six-time intervals (0, 30, 60, 90, 120, and 150days), and microstructure was evaluated at the beginning and the end of the experiment, with scanning electron microscopy (SEM). The highest decomposition was verified for commercial vermicompost rich in macro and micronutrients and with lower P contents. The lignin:N ratio and the initial P content were more important in the permanence of the organic compost in the field than the C:N ratio. Regardless of the organic composts, the use of urea as a mineral fertilizer stimulated decomposition more than the organo-mineral fertilizer. The initial composition of the nutrients was decisive in the dynamics of nutrient release, mass loss, and decomposition of C. There was no pattern in the release order of macronutrients. However, for the micronutrients, the release order was Cu > Fe > Mn, in all treatments. Microstructure analysis is a visual analysis where differences are detected through microphotographs and the biggest difference occurred with millicompost, which showed elongated fibers and fiber bundles, forming a relatively open structure characteristic of the presence of fulvic acid. However, the addition of organo-mineral fertilizer formed agglomerates in compacted micro-portions, helping the mineralization of C and N.

Pore fluid salinity effects on post-stabilization performance of cement-treated Marl

Soil improvement using chemical admixtures has been extensively investigated in the recent past and these admixtures are abundantly being used on various construction projects. However, there is a need to elucidate the long-term performance of stabilized geomaterials under aggressive pore fluid environments such as high salinity of groundwater in coastal areas. This study presents the effects of the concentration of pore fluid salinity on the post-stabilization behavior of cement-treated Marl specimens to brine solution from Sabkha deposits and rejected water from a water treatment plant. Unconfined compressive strength (UCS), mineralogy, chemical, and microstructural evaluations have been carried out in this regard. minerals like albite and muscovite completely leached out of the samples after 28 days of soaking in a saline environment. A new mineral Attapulgite was formed at various concentration levels of the pore fluid. Significant changes in the chemical composition were also observed in various phases of the experiments. Moreover, at all salinity levels, the UCS initially increased to a maximum of 75 % which later reduced to a value less than the original strength whereas the elastic modulus (E50) increased as the soaking period progressed. Lastly, it is emphasized that the engineering properties of treated soils exposed to aggressive pore fluids should be carefully assessed for a reliable prediction of the long-term performance of geotechnical structures.

Microstructural evaluation of interfacial intermetallic compounds between Sn58Bi and ENEPIG

BackgroundLow carbonization and Restriction of Hazardous Substances (RoHS) regulations have promoted the development of low-temperature lead-free solder. The solder and substrate are critical entities of joint connections. MethodsSn58Bi has been considered a promising low-temperature solder. Electroless nickel/electroless palladium/immersion gold (ENEPIG) is a good surface finish that prevents solder joints from oxidizing and extends the shelf life of the substrates. In this study, the interfacial reactions between the Sn58Bi solder and ENEPIG surface finish were systematically analyzed. Findings(Au,Pd,Ni)(Sn,Bi)4 was observed after reflow at 160 °C. Au and Pd dissolved into solder rapidly in the beginning. NiSn4 and Ni3Sn4 with small amounts of Au and Pd dissolution formed at the interface after aging. The morphology of NiSn4 evolved from block-like to needle-shaped and finally to a layered configuration as the aging temperature and time increase. Ni3Sn4 was observed between NiSn4 and substrate above 100 °C. This study established the growth mechanism of intermetallic compounds (IMCs) in the reaction between Sn58Bi and ENEPIG for low-carbon emitting processes.

3D-printed titanium-aluminum-vanadium alloy produced at various laser powers: evaluation of microstructures and mechanical characteristics

3D-printed titanium-aluminum-vanadium alloy produced at various laser powers: evaluation of microstructures and mechanical characteristics

Self-propagating high-temperature synthesis of AlxCoCrFeNiMoy high-entropy alloys: thermochemical modelling, microstructural evaluation and high temperature oxidation behaviour

In this study, the feasibility of the synthesis of AlxCoCrFeNiMoy (0.5 < x < 3, y = 0.5,1) alloys via cost and energy efficient thermochemical modelling assisted (FactSage™) aluminothermic self-propagating high-temperature synthesis (SHS) method was investigated. In addition, selected SHS alloys were also suction-casted into a bar shape by using a vacuum arc melter and the microstructural changes and oxidation behaviour of selected alloys were investigated. The characterization results demonstrated that AlxCoCrFeNiMoy (0.5 < x < 3, y = 0.5,1) master alloys can be successfully synthesized via thermochemical modelling assisted SHS method with a substantial composition control. The microstructures of the SHS alloys were found to comprise of the FCC-A1, BCC (A2, B2) and σ phases with varying fractions depending on the composition. Increasing Al content was found to increase the hardness of the alloys from 278 HV to 829 HV for the AlxCoCrFeNiMo0.5 system. For AlxCoCrFeNiMo system, on the other hand, it had an increasing effect from Al0.5 to Al1.0 (from 659 HV to 903 HV) initially and then decreased the hardness to the levels of 773 HV with the further addition of Al. Suction-cast alloys exhibited rather similar microstructures with similar phase constituents and hardness values. As a general trend primer B2 phase fraction was increased due to higher cooling rate. Oxidation studies revealed that the Al3.0Mo0.5 alloy, which has higher B2 content (919 HV), exhibited better oxidation resistance after 100 h of exposure to air at 800 °C. Postulated scaling mechanisms, supported with the CALPHAD simulations and Raman analyses, revealed the formation of non-protective spinel oxides and sublimation of volatile MoOx oxides before the stabilization of a protective M2O3 (M = Al,Cr) layer, especially for the AlCoCrFeNiMo alloy.

Evaluation of microstructure, corrosion resistance performance, and mechanical properties of 316L austenitic stainless steel FCAW welded joints: a comparative study

ABSTRACT This research aims to not only examine the effect of different mixtures of Ar and CO2 on microstructural features and corrosion behavior of double-pass FCAW of 316L SS but also compare these characteristics with gas tungsten arc welding (GTAW) and self-shielded FCAW. Different shielding gas mixtures, namely 100%Ar, 100%CO2, 82%Ar+18%CO2 were used to make the specimens. All specimens represent biphasic microstructures containing austenite (Ɣ) and delta-ferrite (δ-ferrite). Based on the potentiodynamic (PD) test results, the anti-corrosion protection performance of the welded region was enhanced when using GTAW compared to self-shielded FCAW. Additionally, the impedance value of the GTAW joint was higher than that of the FCAW-welded specimens. The ductility of welded joints was ranked as GTAW > CO2 +Ar shielded FCAW > self-shielded FCAW > CO2 shielded FCAW. The ranking of transverse tensile strength was as follows: CO2 shielded FCAW> self-shielded FCAW > CO2+ Ar shielded FCAW> GTAW.

Evaluation of microstructure and mechanical behavior of a strengthened Al 5083 hybrid composite fabricated by squeezed assisted liquid metallurgy technique

Evaluation of microstructure and mechanical behavior of a strengthened Al 5083 hybrid composite fabricated by squeezed assisted liquid metallurgy technique

Parameter development and characterization of laser powder directed energy deposition of Nb – Alloy C103 for thin wall geometries

This work focuses on the parameter development and microstructural characterization of Nb-based alloy C103 for thin wall structures produced via laser powder – directed energy deposition (LP – DED). Laser power and scanning speeds were varied as part of a design of experiments to identify adequate print parameters. Combinations were evaluated for relative density, porosity, and geometrical accuracy. A combination of a laser power of 1420 W and scanning speed of 14 mm/s resulted in a relative density >99%, exhibited a consistent weld bead profile and was used for further microstructural evaluation. A mix of optical and scanning electron microscopy (SEM) revealed small, slightly elongated grains along the edges and large epitaxial grains in the central region along the Build – Transverse view. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analysis revealed Hf rich columnar cells in the center that transition into an evenly spaced cellular structure towards the edges of the built sample. Electron backscatter diffraction (EBSD) scans show a sharp [001] texture when looking at the cross section of the sample along the build direction. The Build – Scan view revealed a zig – zag pattern that follows the back – and – forth deposition strategy that was used. Finally, microhardness measurements were taken in the as – built (AB) and stress relieved (SR) conditions to baseline preliminary mechanical properties. The AB condition exhibited a large amount of scatter in the data and averages up to 11% larger than the SR condition. The reduction in scatter upon applying the SR cycle are indicative of a large concertation of dislocations present in the AB condition.

Microstructure, mechanical and tribological properties of Mg/CoCrFeNiMoTi high entropy alloy composites produced via FSP

In this study, multi-pass friction stir processing (FSP) was used to produce magnesium (Mg) matrix composites reinforced with CoCrFeNiMoTi high entropy alloy (HEA) particles. The effect of the HEA reinforcements on microstructure evaluation, mechanical properties (hardness and tensile) and wear performance was investigated. The composites were produced with similar pass number (three passes) and tool rotation speed (1250 rpm) and different tool transverse speeds (25 and 50 mm/min) and compared with the Mg matrix without reinforcing particles. XRD results indicated no significant reaction at the interface of the HEA and the matrix during FSP. Microstructure results showed the distribution improvement of the HEA reinforcements and elimination of lamellar structure (inhomogeneous structure) with the decrease of the tool transverse speed from 50 to 25 mm/min. Microstructures of all specimens illustrated four microstructural regions including stirring zone, thermo-mechanical affected zone, heat-affected zone and base metal. The average grain size of the stir zone reduced significantly from 12 µm for the Mg-50 to 2.5 µm and 1.6 µm for the Mg/HEAs-50 and Mg/HEAs-25 composites. The hardness value was increased from 34 HV for the base alloy to 113 HV for the FSPed composite at 25 mm/min (232 % improvement). The maximum yield and tensile strengths were obtained as 86.4 MPa and 114 MPa for the FSPed composite at 25 mm/min which presented enhancement of 92 % and 43 %, respectively as compared with the FSPed Mg alloy. The wear resistance results showed the reduction of the friction coefficient and wear rate with the addition of the HEA reinforcements with a considerable decrease in wear debris, groove depth, micro-cracks and delamination. Comparative plots confirmed that the hardening and strengthening effects of the HEA reinforcements were significantly higher than other reinforcements in Mg matrix composites.

Investigation on the influence of gradation design on the road performance of cold mixed epoxy asphalt mixture based on microstructure evaluation

Cold mixed epoxy asphalt mixture (CMEAM) has excellent anti-deformation and fatigue performance which shows remarkable superiority on bridge pavements. Previous studies have done comprehensive researches on its properties through macroscopic experiments. However, few studies revealed the impact of gradation design on the road property of CMEAM through microscopic method. Thus, in this paper, X-Ray computed tomography (X-ray CT), nanoindentation (NI), field emission scanning electron microscopy (FESEM) and mercury intrusion porosimetry (MIP) are introduced to investigate the coarse aggregates contact degree, the thickness and elastic modulus of interfacial transition zone (ITZ) and the pore diameter distribution of CMEAM. Results showed that the contact points of coarse aggregates in EA-05 mixture are around 40 while those in EA-10 mixture are around 20. (40°, 50°) is the key inclination angle interval for EA-10 mixture type while (70°, 80°) and (10°, 20°) are of significance for EA-05 mixture type. The contact points and inclination angles are positively and inversely proportional to Marshall stability, respectively. In addition, the ITZ thickness of EA-05 and EA-10 mixture is below 10 μm and above 40 μm, respectively. The ITZ elastic modulus of EA-10 mixture is approximately 1.5 times than that of EA-05. The thickness and elastic modulus of ITZ are inversely proportional to low-temperature indirect tensile strain (εT). Meanwhile, EA-05 mixture has higher proportion in gel micropores and middle capillary pores while EA-10 mixture has higher proportion in mesopores and large capillary pores. Mesopores has the highest correlation coefficients with tensile strength ratio (TSR), followed by large capillary pores. The suggested proportion for above two type pores is around 21.5% and 51.0%, respectively.

Experimental full waveform inversion for elastic material characterization with accurate transducer modeling

For quality assurance and in-service safety, sufficient characterization of the materials is essential during the development, manufacture, and processing of a material in any industrial setting. Evaluation of elastic coefficients, material microstructures, morphological features, and related mechanical properties are all part of the process of characterizing a material. Ultrasonic signals are sensitive to material properties such as wave speeds, attenuation, diffusion backscattering, microstructural variation, and elastic characteristics (e.g., elastic modulus, hardness, etc.). Ultrasonic computed tomography (USCT) is an emerging imaging method that can be implemented to obtain a quantitative estimation of material properties. In this study, a source estimation technique was initially proposed to obtain the source time function for accurate forward modeling by constructing a linear inverse problem for the unknown transducer modeling. Finally, a material characterization approach was proposed with accurate source estimation to extract wave speed distribution from an elastic material by employing a wave-based method, known as full waveform inversion (FWI). Systematic performance analysis of the proposed FWI model with accurate source estimation was assessed using experimental and synthetic data obtained from a 6061 aluminum sample. Overall, the proposed FWI technique has successfully reconstructed the wave speed distribution, exhibiting the potential of the proposed method of material characterization in various engineering applications.

Evaluation of Microstructure, Corrosion, and Surface Properties of Plasma-Assisted Oxy-Nitrided Ti–6Al–4V Alloy

Evaluation of Microstructure, Corrosion, and Surface Properties of Plasma-Assisted Oxy-Nitrided Ti–6Al–4V Alloy

Fabrication of soy protein microgels via two top-down methods and characterization of the foaming behavior

The aim of this study was to design and characterize soy protein microgels (SPM) using heat-induced (H-SPM) and enzyme cross-linking (E-SPM) methods, and then compared their conformational differences with soy protein isolate (SPI) and explored their foaming behavior. The results showed that transglutaminase-induced covalent cross-linking could fabricate SPM more effectively than that of simple heat treatment, resulting in larger particle sizes, higher surface charge and lower surface hydrophobicity, as well as more robust internal integrity and more ordered structure. Compared with SPI and H-SPM, the foamability of E-SPM decreased by 18.60% and 25.53%, respectively, while the short-term foam stability (60 min) increased by 20.50% and 5.81%, respectively. In terms of long-term foam stability, the foam volume of SPI and H-SPM eventually disappeared after standing for 300 min, while E-SPM still had a considerable foam volume (11.33 mL). Microstructure evaluation suggested that E-SPM stabilized foams via a Pickering-type mechanism. This study will facilitate the applications of SPM as a plant protein-based Pickering-type foam stabilizer in terms of generating aerated foods with long-term foam stability.